There are many choices for siding that you can choose from. Cement board house siding can be one of the strongest options. Cement board siding can withstand extreme temperatures, rain and wind. It is also non-pest-friendly. It is an excellent choice for Fort Worth, TX homes.
There are two main types: cement boards. The first is made with Portland cement. The second is made from a combination of cement fibers and plant fibers. These fibers give board its strength and flexibility. The fibers can be pulverized in water, and then mixed with a variety additives. The typical cement fiber board contains up to eight percent cellulose, forty to sixty percent cement and twenty to thirty percent cellulose fillers.
You may need to use screws if you intend on installing a cementboard over a steel or wood frame. For strength, you will want to use screws with a ring shank. It is important that screws are flush to the surface. You should also ensure that the screws are not too deep to weaken the board's hold.
You must ensure that the cement board is properly ventilated before you can install it. If you have too little airflow, you'll have mold problems. Installing the board in a location where it will be exposed to moisture is a good idea. You'll need to add a waterproofing layer to the board. You can also add a water barrier to stop water from entering the space. These materials are available at your local hardware store.
Before you start installing your cementboard, you need to measure the room. To allow for heat expansion, you will need at least a quarter of an inch between each board. It's a good idea to use a drywall T-square to determine your measurements. You will need to attach the board onto a thin layer o adhesive mortar.
After installing the cement board, seal the joints with silicone caulk. This will prevent any leaks. A drywall screw can be used to attach the board on the wall. It is best to pre-drill fasteners. A ring shank nail can be used if you don’t own a screw for drywall.
You will need a backing if you plan to install your board on top of brick or tile. This will prevent tiles from cracking. You'll also need to use a water-resistant compound to help keep the tiles from moving. This is especially important when the area is exposed to moisture. If your space is subject to water spray or showers, you will need to waterproof it. If you plan on installing the cement board to a floor you can use a vapor barrier. You can also use a drywall screw and a ring shank nail to attach the board to the floor.
For cutting the cement board you will need a saw and grinder. A carbide-tipped cutter blade will also be needed. It is best that the board be cut in a well-ventilated location. This will help avoid the skunky smell that comes from cutting the cement board.
FAQ
Do I require permits to renovate a house?
Permits are required before you can start any home improvement project. In most cases, you will need a building permit and a plumbing permit. You might also require a zoning permission depending on which type of construction is being undertaken.
What room should I remodel first?
The kitchen is the heart of any home. It is where you spend your most time cooking, entertaining, eating, and relaxing. If you're looking to make your kitchen more functional, attractive and beautiful, this is the place for you!
It is also an important component of any home. It provides comfort and privacy while you take care of everyday tasks, such as bathing, brushing teeth, shaving, and getting ready for bed. These rooms can be made more functional and attractive by installing storage space, a shower, or replacing older fixtures with newer models.
What should I fix first when renovating a house?
Fixing up a home starts with cleaning out all the clutter from inside and outside. You will need to clean out all moldy areas and repair any leaky pipes. Finally, you'll need to repaint the interior. You will need to clean up the exterior and paint.
What is the cost of renovating a house?
Renovations are usually between $5,000 and $50,000. Renovations typically cost homeowners between $10,000 and $20,000
Statistics
- Design-builders may ask for a down payment of up to 25% or 33% of the job cost, says the NARI. (kiplinger.com)
- A final payment of, say, 5% to 10% will be due when the space is livable and usable (your contract probably will say "substantial completion"). (kiplinger.com)
- ‘The potential added value of a loft conversion, which could create an extra bedroom and ensuite, could be as much as 20 per cent and 15 per cent for a garage conversion.' (realhomes.com)
- They'll usually lend up to 90% of your home's "as-completed" value, but no more than $424,100 in most locales or $636,150 in high-cost areas. (kiplinger.com)
- Most lenders will lend you up to 75% or 80% of the appraised value of your home, but some will go higher. (kiplinger.com)
External Links
How To
How do I plan for a whole house renovation?
Planning a whole-house remodel requires planning and research. Before you start your project, here are some things to keep in mind. The first thing you need to decide is what kind of home improvement you want to make. There are many options available, including kitchen, bathroom and bedroom. Once you've chosen the category you want, you need to decide how much money to put towards your project. If you are new to working in homes, budget at least $5,000 for each room. If you have some previous experience, you may be capable of getting away with a lower amount.
Once you've determined the amount of money you can spend, you need to decide how large a job you want. A small kitchen remodel will not allow you to install new flooring, paint the walls, or replace countertops. On the other side, if your budget allows for a full renovation of your kitchen, you'll be able do just about any task.
Next, you need to find a contractor who is experienced in the type project that you want. You'll get high-quality results and save yourself lots of headaches down the line. After finding a good contractor, you should start gathering materials and supplies. You may need to purchase everything from scratch depending on the size and scope of your project. However, it is possible to find everything you need in a variety of shops that sell premade items.
Once you've collected all the materials you will need, you can begin to plan. You will first need to sketch out an outline of the areas you plan to place appliances and furniture. Next, plan the layout. Be sure to leave enough room for electric outlets and plumbing. Make sure to position the most visited areas close to the front door. Visitors can also easily access them. You can finish your design by choosing colors and finishes. Avoid spending too much on your design by sticking to simple, neutral colors and designs.
Now it's time for you to start building. It's important that you check the codes in your area before you start construction. Some cities require permits. Others allow homeowners to build without permits. To begin construction you will first need to take down all walls and floors. Next, you'll need to lay plywood sheets in order to protect your new floors. Next, you will nail or screw together pieces wood to create the frame for your cabinets. Finally, attach doors and windows.
There are some final touches that you will need to make after you are done. You might want to cover exposed pipes or wires. You will need to use tape and plastic sheeting for this purpose. You'll also want to hang pictures and mirrors. Keep your work area tidy and clean at all times.
If you follow these steps, you'll end up with a beautiful, functional home that looks great and saves you lots of money. You now have the knowledge to plan a complete house remodel.